Silver Saturn Ring Ornament Free Crochet Pattern
Silver Saturn Ring Ornament Free Crochet Pattern
Introduction
This little ringed planet is the perfect quick project for anyone who loves space, science, or something a bit different on the tree. It is a beginner-friendly pattern built from just two simple shapes: a small stuffed ball and a flat crocheted strip that wraps around it as a ring. The ice blue sphere looks cool and frosty, and the silver band gives it a clean, modern shine. Worked in worsted-weight acrylic at a firm gauge, the finished ornament is about 2.5 inches across the ball and 3.5 inches across the ring, so it feels light in the hand and sits neatly on a branch. If you can single crochet, increase, and decrease, you can make this ornament today.
Materials Needed
- Yarn: (4) Medium Weight/Worsted Weight acrylic. Color A (ice blue): 30 yd. Color B (silver): 10 yd.
- Hook: 5 mm (H/8).
- Notions: Stitch marker, tapestry needle, scissors, polyester fiberfill for stuffing, rust-proof pins for pinning the ring.
- Finished size: Ball 2.5 inches diameter; ring 3.5 inches outer diameter.
Abbreviations
- ch – chain: make a loop of yarn and pull another loop through it.
- sc – single crochet: insert hook, pull up a loop, yarn over, pull through both loops.
- inc – increase: work 2 single crochet into the same stitch.
- dec – decrease: work 2 single crochet together into one stitch.
- MR – magic ring: an adjustable loop you crochet into, then pull closed.
- st(s) – stitch(es).
- rnd(s) – round(s).
- FO – fasten off: cut yarn and pull the tail through the last loop.
Gauge
4 sc = 1 inch and 4 rnds = 1 inch. To check, crochet a small flat swatch of single crochet and measure a 1-inch section; adjust your hook size if your stitches are much larger or smaller than this.
Tips Before You Start
- Work the ball in continuous rounds without joining, and place a stitch marker in the first stitch of each round so you never lose your place.
- Stuff the ball firmly but in small pieces, adding the last bit just before the final decrease round so the sphere stays round and smooth.
- Keep your single crochet tension even on the ring strip so it lies flat; a tight, curling strip will be hard to pin around the ball.
- Pin the ring in place before sewing so you can adjust the tilt and make sure the ball sits centered inside the loop.
Step-by-Step Instructions
Ball (Color A)
Rnd 1: MR, 6 sc into the ring (6 sts). Pull the ring closed.
Rnd 2: inc in each st around (12 sts).
Rnd 3: [sc, inc] x6 (18 sts).
Rnd 4: [2 sc, inc] x6 (24 sts).
Rnd 5: [3 sc, inc] x6 (30 sts).
Rnds 6-10: sc in each st around (30 sts).
Rnd 11: [3 sc, dec] x6 (24 sts).
Rnd 12: [2 sc, dec] x6 (18 sts).
Rnd 13: [sc, dec] x6 (12 sts). Stuff the ball firmly.
Rnd 14: dec x6 (6 sts). FO, leaving a tail. Thread the tail through the remaining 6 sts and pull closed.
Ring (Color B)
Row 1: Ch 36. Sc in the 2nd ch from hook and in each ch across (35 sts).
Rows 2-3: Sc in each st across (35 sts). FO, leaving a long tail for sewing.
Assembly and Finishing
Thread the long tail of the ring onto your tapestry needle and sew the two short ends together to form a closed loop, matching the rows so the strip lies flat. Slip the loop over the ball and pin it in place at a slight angle, with the ball centered inside the ring. Using Color B, sew the ring to the ball at 4 evenly spaced points around the ball, catching the ring strip and the ball surface at each point. Remove the pins. Weave in all ends securely. If you want to hang the ornament, use Color B to attach a small hanging loop to the top of the ball. Block lightly if needed by misting the ring and pressing it flat under a cloth, then let it dry completely.
Pro Tips and Variations
- Swap the ice blue for a deep navy or lavender ball and keep the silver ring for a different planet look.
- Add a thin strand of metallic thread held together with Color A for a subtle sparkle on the sphere.
- Make a set in different sizes by using a smaller hook and lighter yarn for mini planets, or hang several from one ribbon as a garland.
