Denim Blue Crochet Water Bottle Holder Free Pattern

Introduction

This denim blue crochet water bottle holder is the perfect little project for anyone who wants a practical, hands-free way to carry their water. It's worked in simple single crochet rounds, so it's a great fit for advanced beginners who are comfortable with a magic ring and basic increases. The straight-sided body in denim blue with a crisp cream band at the top gives it an easy, western-inspired look, and the long cross-body strap lets you sling it over your shoulder and go. The cotton yarn makes it sturdy enough to hold a full bottle while still feeling soft and comfortable against your body.

Materials Needed

• Yarn: Worsted weight cotton yarn — approximately 100 yards (91 m) denim blue (Color A) and 20 yards (18 m) cream (Color B)
• Hook: 5.0 mm (H-8) crochet hook
• Notions: Stitch marker, tapestry needle, scissors, measuring tape
• Finished size: Approximately 3.5 inches (9 cm) in diameter and 8 inches (20 cm) tall, excluding the strap; strap length 48 inches (122 cm)

Abbreviations

• ch — chain: make a loop of yarn and pull it through the loop on your hook
• sc — single crochet: insert hook into stitch, yarn over, pull up a loop, yarn over, pull through both loops
• inc — increase: work 2 single crochet stitches into the same stitch
• st(s) — stitch(es)
• rnd(s) — round(s): a complete circle of stitches worked in the round
• MR — magic ring: an adjustable loop you crochet into to start a round piece
• rep — repeat

Gauge

16 single crochet stitches and 16 rounds = 4 inches (10 cm). To check, crochet a small swatch in single crochet rounds and measure a 4-inch section; if you have more stitches than 16, go up a hook size, and if you have fewer, go down.

Tips Before You Start

• Use a stitch marker in the first stitch of each round — this holder is worked in continuous rounds, so the rounds spiral and the marker keeps you on track.
• Keep your tension even and fairly firm; a slightly tighter single crochet gives the holder more structure so it stands up on its own.
• Check the fit as you go: after Round 10, the base should measure about 3.5 inches across. If your bottle is wider or narrower, adjust by adding or removing one increase round.
• Don't cut Color A until you've finished the cream band — you'll need a length of it later to sew on the strap.

Step-by-Step Instructions

Holder (Color A, then Color B)

Work in continuous rounds; do not join or turn unless told. Place a marker in the first stitch of each round.

Rnd 1: MR, 6 sc into the ring (6 sts)

Rnd 2: inc in each st around (12 sts)

Rnd 3: [sc, inc] x6 (18 sts)

Rnd 4: [2 sc, inc] x6 (24 sts)

Rnd 5: [3 sc, inc] x6 (30 sts)

Rnd 6: [4 sc, inc] x6 (36 sts)

Rnd 7: [5 sc, inc] x6 (42 sts)

Rnd 8: [6 sc, inc] x6 (48 sts)

Rnd 9: [7 sc, inc] x6 (54 sts)

Rnd 10: [8 sc, inc] x6 (60 sts)

Rnd 11: sc in each st around (60 sts)

Rnds 12–30: sc in each st around (60 sts)

Change to Color B.

Rnds 31–33: sc in each st around (60 sts)

Fasten off.

Strap (Color B)

Worked flat in rows.

Row 1: Ch 4, sc in 2nd ch from hook and in each ch across (3 sts)

Row 2: Ch 1, turn, sc in each st across (3 sts)

Rows 3–onward: Rep Row 2 until the strap measures 48 inches (122 cm). Fasten off.

Assembly and Finishing

Lay the holder flat and find the two opposite points at Round 33 (the cream top edge) where you want the strap to sit. On each side, attach the strap ends 1 inch apart using Color A: thread a tapestry needle with denim blue yarn and sew each strap end firmly to the top edge with several small, secure stitches through both layers. Weave in all ends on the inside of the holder and along the strap. Block lightly by misting with water and shaping the holder over a bottle or jar so it dries round and upright; let it air dry completely before use.

Pro Tips and Variations

• Swap the cream band for a contrasting color like mustard or rust for a bolder western look, or work the whole holder in one color for a minimalist version.
• Make the strap adjustable by crocheting it slightly longer and adding a simple button or knot closure at one end.
• For extra durability, work the base rounds with a smaller hook (4.5 mm) and switch to the 5.0 mm hook for the sides.