Winter Berry Spike Crochet Bralette Free Pattern

Winter Berry Spike Crochet Bralette Free Pattern

Introduction

This little bralette is made for teens and anyone with a 30–32 in bust who wants a cozy, handmade layer that feels as good as it looks. It is worked as one simple tube in the round, so there is no shaping, no tricky decreases, and no sewing of curved pieces — just straight single crochet with a few fun spike rounds for texture. The chocolate and caramel color story gives it a warm, Scandinavian feel, and the tiny caramel flower at center front makes it feel special without being fussy. It works up quickly in aran weight yarn, so it is a great first garment project or a fast weekend gift.

Materials Needed

• Yarn: Aran weight wool blend (for example 80% acrylic, 20% wool; 170 yd / 100 g). Color A (chocolate): 90 yd. Color B (caramel): 30 yd.
• Hook: 5.0 mm (US H-8), or the size needed to match gauge.
• Notions: Tapestry needle, stitch marker, scissors, measuring tape, rust-proof pins for blocking.
• Finished size: To fit teen bust 30–32 in (76–81 cm). Band circumference 28 in (71 cm), height 6 in (15 cm).

Abbreviations

• ch — chain: make a loop of yarn and pull it through the loop on your hook.
• sc — single crochet: insert hook, pull up a loop, yarn over, pull through both loops.
• sl st — slip stitch: insert hook, yarn over, pull through everything on the hook at once.
• yo — yarn over: wrap the working yarn over your hook.
• st(s) — stitch(es).
• rnd(s) — round(s).
• rep — repeat.
• MR — magic ring: an adjustable loop used to start a small circle.
• spike — a single crochet worked into the front loop of a stitch 2 rounds below, creating an elongated stitch.

Gauge

14 sts and 16 rnds = 4 in (10 cm) in the spike stitch pattern. To check it, work a small swatch in the round (or a flat swatch of sc and spike rounds) and measure a 4 in section in the middle — if you have more stitches than 14, go up a hook size; if fewer, go down.

Tips Before You Start

• When you join the starting chain into a ring, check carefully that it is not twisted before you work Round 1 — a twist here cannot be fixed later.
• Keep your spike stitches loose enough to reach comfortably down 2 rounds; pulling them tight makes the band pucker.
• Use a stitch marker at the start of each round so you always know where to join.
• Change colors at the very end of the last stitch of a round, working the final yarn-over of the join with the new color for a clean transition.

Step-by-Step Instructions

Band (Color A)

Setup: Ch 98, join with sl st to first ch to form a ring, being careful not to twist.

Rnd 1: Ch 1, sc in each ch around, join with sl st to first sc (98 sc).

Rnd 2: Ch 1, sc in each st around, join (98 sc).

Rnds 3–4: Rep Rnd 2 (98 sc).

Rnd 5 (spike rnd): Ch 1, sc in first st, *insert hook in front loop of sc 2 rnds below, yo, pull up loop, yo, pull through both loops on hook (spike made), sc in next st; rep from * around, join (98 sts).

Rnd 6: Ch 1, sc in each st around, join (98 sc).

Rnd 7: Rep Rnd 5 (98 sts).

Rnd 8: Rep Rnd 6 (98 sc).

Change to Color B.

Rnd 9: Rep Rnd 5 (98 sts).

Rnd 10: Rep Rnd 6 (98 sc).

Change to Color A.

Rnd 11: Rep Rnd 5 (98 sts).

Rnd 12: Rep Rnd 6 (98 sc). Fasten off.

Flower Appliqué (Color B)

Center: MR, 5 sc into ring, join with sl st to first sc (5 sc).

Rnd 1 (petals): Ch 1, [sc in next sc, ch 2, sl st in same sc] 5 times (5 petals). Fasten off, leaving a 6 in (15 cm) tail for sewing.

Straps (Color A) — make 2

Row 1: Ch 30, sc in 2nd ch from hook and in each ch across (29 sc). Fasten off, leaving a 6 in (15 cm) tail.

Assembly and Finishing

Pin the flower to the center front of the band and sew it in place using the 6 in tail, catching only the back of the petals so the stitches stay hidden. Attach one end of each strap to the top edge of the band at the front, 3 in (7.5 cm) from the center on each side. Attach the other end of each strap to the back edge directly opposite the front attachment point, forming two shoulder straps over the tube. Try the bralette on before you weave in the strap ends so you can adjust the length if needed. Weave in all ends on the wrong side. Block lightly by misting with water and pinning the band to its finished measurements (28 in circumference, 6 in height), then let it dry flat — do not stretch the spike rounds.

Pro Tips and Variations

• Swap the caramel accent rounds for a deep berry red to match the name, or use a self-striping yarn for the spike rounds.
• Make the straps adjustable by adding a small button at the back edge and working a few extra chains into a loop at the strap end.
• For a slightly longer band, add pairs of spike and plain sc rounds before the final chocolate rounds — each pair adds about ½ in (1.25 cm) of height.